Threaded metal tube that runs between the heater block and the circular heatsink in the extruder
FeaturesSpecsSupport
Genuine Flashforge Part.
Next >
- Thread: M7
- Overall length: 26.6mm
- Inner (Bore) Diameter: 4.1mm
- Threaded along its entire length, with the thread turned off for 2.2mm, 7.5mm from one end
- Does not suite Flash Forge high temp Heat sink
- Red fan cover
Product Dimensions: 26 x 7 x 7mm
Next >
This product has no specific warranty. Bilby 3D will honor obligations under Australia Consumer Guarantee regulations if and where they apply to this product
This stainless steel barrel has continuous thread so it is more universal than our standard barrel. It also has been drilled out larger at one end and a piece of teflon (PTFE) tube inserted to reduce the chances of "barrel lock" which can stop filament feeding resulting in a failed print and otherwise only solved with the oily rag trick (see our support articles)
Buy Now
Teflon tube for Flashforge Single Extruder Barrel - FFptfe
This short piece of Teflon tubing is for lining the barrel on the Flashforge Guider, Guider2, Finder, Finder Plus and Inventor 2
Buy Now
Capricorn Teflon tube for Flashforge Single Extruder Barrel - FFptfe
This short piece of Teflon tubing is for lining the barrel on the Flashforge Guider, Guider2, Finder, Finder Plus and Inventor 2
Made from Capricorn Tubing, it is higher lubricity and more resistant to the high temperatures experiences in a hot end
Buy Now
Extruder Heatsink for Inventor 2, 2S and 2 Special Edition-FFptfe-FFtc
Genuine FlashForge replacement part
Buy Now
Heater Cartridge for the Guider 2, Inventor 2/2s/se (24V, 18.5 long)-FFptfe-FFtc
Genuine FlashForge replacement part for the Guider 2 (NOT THE GUIDER 1-see specs tab), Inventor 2/2S/2SE
Stainless Steel Nozzle for MK10 Extruders (with 7mm threads)
Buy Now
FlashForge Thermocoupler - Short with Molex connector
Genuine FlashForge thermocoupler with 11cm lead length and Molex connector for the Finder, Inventor2 and Guider Series which have a terminal board on the extruder carriage.
Buy Now
Extruder Heatsink for Guider 2S - High Temperature Version - FFam
Genuine FlashForge replacement part
For the High-Temp (300°C) hotend with the red cooling duct
Buy Now
0.6mm Brass Nozzle for FlashForge All Metal Hot Ends - FFam
When the FlashForge Guider2S switched over to a high-temperature hot end, it came with a different nozzle and barrel/heatbreak (with red nozzle duct)
Buy Now
FlashForge Nozzle Set for Guider 2 High-Temp Hotends - FFam
Nozzle set with toughened drive gear and tools for the Guider2S with a high-temperature hotend. This will have a RED nozzle duct
Buy Now
0.4mm Toughened Nozzle for FlashForge All Metal Hot Ends - FFam
When the FlashForge Guider2S switched over to a high-temperature hot end, it came with a different nozzle and barrel/heatbreak (with red nozzle duct)
Buy Now
Heater Block for FlashForge Guider 2S HT - FFam
Genuine FlashForge spare part
this heater block suits those G2S with the High-Temp (300°C) hotends
Does Not include Grub screw or Bolt
Buy Now
FlashForge Hot End Assembly for Guider2s - 300°C - FFam
Genuine Flashforge HotEnd Assembly for the Guider2S
With a brass 0.4mm nozzle and is rated to 300 °C
Buy Now
Teflon Tube for FlashForge Guider 2 - High Temp HotEnd - FFam
26mm length to suit ptHotEndAssFFg2HT - made from Capricorn PTFE Tube
Buy Now
Heater Block for the FlashForge Finder, Guider, Inventor 2-FFptfe-FFtc
Genuine heater block for the FlashForge Finder series, Guider Series and Inventor 2
Buy Now
0.4mm Nozzle for FlashForge All Metal Hot Ends - FFam
When the FlashForge Guider2S switched over to a high-temperature hot end, it came with a different nozzle and barrel/heatbreak (with red nozzle duct)
All prices are in Australian Dollars and include GST. Standard Postage & Handling with Australia is $12 flat rate, free for orders over $350. Express Post starts at $15
Sydney - Kingsgrove, NSW
Melbourne - Clayton, VIC
