All Metal Hot End Assembly for FlashForge Guider 2 / 2S-FFtc
This is a slot in replacement for FlashForge machines with a cylindrical heatsink and 24V heater cartridge
FeaturesSpecsSupport
This all metal hotend with toughened (and non-stick) nozzle means less maintenance and longer life - for all materials, but especially important if printing with abrasives such as carbon fibre.
Slot in replacement for the following models:
- Guider 2
- Guider 2S
Built with a mix of Genuine FlashForge parts and the Micro-Swiss All Metal hotend upgrade.
Next >
Includes:
- FlashForge Heater block
- MicroSwiss TwinClad Nozzle
- MicroSwiss HeatBreak / Barrel
- FlashForge cylindrical heatsink
- Ceramic Tape
- FlashForge Thermocoupler with connector
- FlashForge Heater Cartridge (24V, 40W)
All assembled and measure to spec by our technicians
Note: This assembled Hot End length once the heatsink attached the overall length is around 57.9mm. It will be slightly longer than original but still fits. However you MUST run Extruder calibration and then Level Routine after fitting. See this fact sheet
Product Dimensions: 100x40x40mm
Next >
This product has no specific warranty. Bilby 3D will honor obligations under Australia Consumer Guarantee regulations if and where they apply to this product
MicroSwiss All Metal Hotend Kit for FlashForge Finder, Guider, Inventor 2/2S/2SE-FFtc
Genuine Micro-Swiss all metal hotend upgrade for the FlashForge Guider, Guider 2
Finder, FinderPlus and Inventor2 recomend - ptKitMK10TC3
Comes with 0.4mm nozzle, range of other sizes available
Buy Now
Heater Block for the FlashForge Finder, Guider, Inventor 2-FFptfe-FFtc
Genuine heater block for the FlashForge Finder series, Guider Series and Inventor 2
Buy Now
FlashForge Thermocoupler - Short with Molex connector
Genuine FlashForge thermocoupler with 11cm lead length and Molex connector for the Finder, Inventor2 and Guider Series which have a terminal board on the extruder carriage.
Buy Now
Heater Cartridge for the Guider 2, Inventor 2/2s/se (24V, 18.5 long)-FFptfe-FFtc
Genuine FlashForge replacement part for the Guider 2 (NOT THE GUIDER 1-see specs tab), Inventor 2/2S/2SE
Buy Now
Extruder Heatsink for Guider 2S - High Temperature Version - FFam
Genuine FlashForge replacement part
For the High-Temp (300°C) hotend with the red cooling duct
Buy Now
0.3mm Brass Nozzle for FlashForge HighTemp Hot Ends - FFam
When the FlashForge Guider2S switched over to a high-temperature hot end, it came with a different nozzle with a longer thread and barrel/heatbreak (with red nozzle duct)
Buy Now
0.6mm Brass Nozzle for FlashForge All Metal Hot Ends - FFam
When the FlashForge Guider2S switched over to a high-temperature hot end, it came with a different nozzle and barrel/heatbreak (with red nozzle duct)
Buy Now
FlashForge Nozzle Set for Guider 2 High-Temp Hotends - FFam
Nozzle set with toughened drive gear and tools for the Guider2S with a high-temperature hotend. This will have a RED nozzle duct
Buy Now
High Temp Barrel for FlashForge Guider2S - FFam
The short barrel / throat / heatbreak for the FlashForge High Temperature hotend, found on leter version of the FlashForge Guider2s (with a red nozzle duct)
Buy Now
0.4mm Toughened Nozzle for FlashForge All Metal Hot Ends - FFam
When the FlashForge Guider2S switched over to a high-temperature hot end, it came with a different nozzle and barrel/heatbreak (with red nozzle duct)
Buy Now
Heater Block for FlashForge Guider 2S HT - FFam
Genuine FlashForge spare part
this heater block suits those G2S with the High-Temp (300°C) hotends
Does Not include Grub screw or Bolt
Buy Now
FlashForge Hot End Assembly for Guider2s - 300°C - FFam
Genuine Flashforge HotEnd Assembly for the Guider2S
With a brass 0.4mm nozzle and is rated to 300 °C
Buy Now
Teflon Tube for FlashForge Guider 2 - High Temp HotEnd - FFam
26mm length to suit ptHotEndAssFFg2HT - made from Capricorn PTFE Tube
Buy Now
0.4mm Nozzle for FlashForge All Metal Hot Ends - FFam
When the FlashForge Guider2S switched over to a high-temperature hot end, it came with a different nozzle and barrel/heatbreak (with red nozzle duct)
All prices are in Australian Dollars and include GST. Standard Postage & Handling with Australia is $12 flat rate, free for orders over $350. Express Post starts at $15
Sydney - Kingsgrove, NSW
Melbourne - Clayton, VIC
