Teflon Tube - 2mm ID, 4mm OD - For 1.75mm Filament
Teflon (PTFE) tube is used to make filament feeder and Bowden tubes.
FeaturesSpecsSupport
This tube has a thicker wall so cannot be used to line barrels. They greatly reduce the chance of snagging between your filament spool and the extruder head without causing much drag.
This is used as bowden tubes on CR-10, Ender and Anet machines, though some do vary so please check your tube before ordering.
Order by the metre. 1m should be enough for a single extruder machine.
Inner Diameter: 2mm
Outer Diameter: 4mm
Clear in colour
This product has no specific warranty. Bilby 3D will honor obligations under Australia Consumer Guarantee regulations if and where they apply to this product
These metal fittings are used for holding pneumatic (compressed air) tube. Designed for tube with a 4mm diameter made of Nylon or PU (PolyUrethane), they also work better than anything else we have found with PTFE tubing, which is very hard to hold due to its low friction. Has plastic collar - push down to release.
Buy Now
Push-In Hose Fitting - for 4mm tube, M6 Thread
These metal fittings are used for holding pneumatic (compressed air) tube. Designed for tube with a 4mm diameter made of Nylon or PU (PolyUrethane), they also work better than anything else we have found with PTFE tubing, which is very hard to hold due to its low friction. Has plastic collar - push down to release.
Buy Now
Push-In Hose Fitting - for 4mm Tube, 3/8in Thread
These metal fittings are used for holding pneumatic (compressed air) tube. Designed for tube with a 4mm diameter made of Nylon or PU (PolyUrethane), they also work better than anything else we have found with PTFE tubing, which is very hard to hold due to its low friction. Has plastic collar - push down to release.
Buy Now
PTFE Tube Cutting Tool - Capricorn Brand
To properly seat your Bowden tube, it is imperative to have a clean, square, end.
Buy Now
Teflon Tube - 2mm ID, 3mm OD
This teflon (PTFE) tube is used to make filament feeder tubes (or line the barrel on older 3mm J-Heads). They greatly reduce the chance of snagging between your filament spool and the extruder head without causing much drag.
Order by the metre. 1m should be enough for a single extruder machine.
Inner Diameter: 2mm
Outer Diameter: 3mm
Buy Now
Teflon Tube - 3mm ID, 4mm OD
A Teflon Tube for feeding 2.85mm filament into a Bowden type extruder
Suitable replacement for Raise3D feeder tube (use 70-75cm lenth)
Buy Now
All Metal Hotend Kit for CR-10 Printers
All Metal Hotend Kit for CR-10 Printers
Includes a silicon heat block cover (not shown)
Buy Now
All Metal Hotend Kit for CR-10s PRO Printers
All Metal Hotend Kit for Creality CR-10s PRO / CR-10 Max / Ender 3 Neo / Ender 3 V2 Neo
Buy Now
Capricorn PTFE Tube - XS High Lubricity - For 2.85/3mm filament
Genuine Capricorn Premium High Lubricity PTFE tubing by the meter
Buy Now
Roller Spool Stand - 140mm wide
Bilby3D designed and 3D printed spool stand for 114mm wide spools.
Our 2020 design is bigger and stronger. It accomodates our 3kg spools, but will also carry our 1kg and 600g spools
All prices are in Australian Dollars and include GST. Standard Postage & Handling with Australia is $12 flat rate, free for orders over $350. Express Post starts at $15
Sydney - Kingsgrove, NSW
Melbourne - Clayton, VIC
