MicroSwiss All Metal Hotend Kit for FlashForge Finder, Guider, Inventor 2/2S/2SE-FFtc
Genuine Micro-Swiss all metal hotend upgrade for the FlashForge Guider, Guider 2
Finder, FinderPlus and Inventor2 recomend - ptKitMK10TC3
Comes with 0.4mm nozzle, range of other sizes available More
Genuine replacement hotend for the Raise3D Pro3 HyperSpeed Hotend Assembly.
This is the hotend only, for the hotswap assembly, see related products More
All Metal Hot End Assembly for FlashForge Inventor 2/2SE-FFtc
This is a slot in replacement for FlashForge machines with a cylindrical heatsink and 24V heater cartridge. This edition has the shorter heat sink (see more information page) More
Genuine Micro-Swiss all metal hotend upgrade for MK10 style extruders.
MK10 Extruders most notibly used on the FlashForge Dreamer, Inventor1 and Creator Pro 2016 and Dremel Idea Builder. It also fits the Wanhao i3 and Cocoon More
These straight cut gears have the advantage over a hobbed gear in that the profile of the teeth is much deeper - so they dont get clogged as quickly - they get a better grip on the filament for longer. More
Heater Cartridge for Dreamer and Inventor 1 only-FFD > UNTIL SOLD OUT
Genuine Spare part for FlashForge Dreamer and Inventor 1 only heater cartridge.
Note : Flashforge CreatorPro cable is different (see image 3, ptHeatCart4024)
Flashforge Finder, Guider (1 and 2) and Inventor2 also have a short heater. This is not compatible
More
This 1 inch wide ceramic tape is used to wrap your heater block and reduce heat transfer to both the extruder and your work piece. Fix by wrapping in kapton tape.
The tape on your Reprap will need replacing from time to time, especially when a print fails and the melted plastic gets caught up in the print head - it can sometimes stick to the ceramic tape and rip it on removal - careful not to pull on the temperature sensor wire! More
Hot End - E3D v6 clone - 1.75mm Filament, 0.4mm nozzle
This complete hot end is based on the All-Metal J-Head design as modified by E3D (V6). Includes everything you need, hot-end wise for 1.75mm filament More
This complete hotend kit from RepRap discount includes; nozzle, heater block, barrel/heat barrier, fined heat sink, heater cartridge, thermistor, fan, mount and more in a plastic case More
This heater cartrige has short (10cm long) cables with a molex male pin connector. The cartrige is 23mm long and 6mm in diameter. It is made in Australia by Bilby3D and is a non-genuine exchange for the Makerbot Replicator 2 and 2X heater cartrige. More
Micro Swiss Bowden Dual Gear Extruder features the same quality construction as the Direct Drive extruders. It is designed to be a bolt-on replacement to most of the Bowden extruder machines on the market. More
This tough extruder includes a greabox for extra filament feeding torque as well as everything you need to take filament from you spool through to pushing it into your hotend.
This tube is an improvement over the stock MakerBot Replicator 1 and MakerBot Replicator 2 thermal barrier tube. Also used on many other types of 3D Printers More
Hot End - E3D v6 clone - 1.75mm Filament, 0.4mm nozzle - Direct Drive
This complete hot end is based on the J-Head design as modified by E3D (V6). Includes everything you need, hot-end wise for 1.75mm filament.Note this is a PTFE lined system
Designed for extruders using direct drive filament feeding (2mm hole at top) More
Upgrade your E3D Volcano HotEnd with the SuperVolcano for super fast printing.
This genuine E3D SuperVolcano kit includes:
Heat-block, 80W Heater, Thermistor and 1mm nozzle. More
Upgrade your Modix 3D Printer to dual extruder
Dual Extruders allow you to print in 2 colours (but not mix them), or Model and Support materials
This is the REAR or second extruder, and can not be used to replace the FRONT/Primary extruder More
Please note: The signal line only supports the 3D touch sensor produced by trianglelab. We are not sure if the sensors of other merchants are compatible. We are also not sure if BL TOUCH is compatible. Please confirm that your sensor was manufactured by TriangleLab before purchasing. More
Micro Swiss NG Extruder for Creality Ender 6 Printers
Micro Swiss NG™ Direct Drive Extruder
This extruder overcomes the shortcomings of all current counterparts on the market, to create an optimal printing experience for everyone. More
Micro-Swiss FlowTech Hotend for Creality K1 and K1 Max
The FlowTech™ Hotend is a new generation hotend line from Micro Swiss. Its unique design eliminates common hotend issues such as leaking nozzle seal and complex nozzle swaps. More
Replicator 1/2 - Extruder Upgrade Kit (injection moulded) - Left Lever
This injection molded upgrade is designed to fit the Makerbot Replicator 1 Twin left extruder. IT DOES NOT FIT the Repliactor 2X which requires a thicker drive system. It also is NOT suitable for the Replicator 2 or single extruder machines! More
Sydney - Kingsgrove, NSW
Melbourne - Clayton, VIC
