0.4mm Nozzle for MK10 Micro Swiss All Metal MK10 Hotend Kit-FFtc
This is Micro Swiss MK10 All Metal Hotend ONLY style nozzle, it will ONLY fit the New MK10 All Metal Hotend. This nozzle has completely different internal dimensions to work with our Micro Swiss thermal barrier tube More
PLA Blend Filament - Magnetic Iron - 1.75mm - 125g Coil - UNTIL SOLD OUT
This amazing filament is a blend of PLA and carbon Fibre by ProtoPasta in the USA.
Proto-pasta Magnetic Iron PLA - as its name implies - responds to magnets and behaves similarly to pure iron, even to the point of rusting! Magnetism opens up a new world of practical applications and fun creations.
It extrudes at 190-200 degrees c on a cold bed. We have tested on buildtak wit glue stick and it sticks well. Prints best at thicker resolutions like 300 microns, but will look like 100 micron. Our tests showed no spider webbing at all, and models held water after printing. It can lift in unsupported areas, but quickly recovers on the next layer. Sands nicely with very course sandpaper. Can get rust effect by submerging in with salty water for 2-3 hours. In our tests it was not too abrasive on nozzle, but recommend a wear resistant nozzle. More
PolyMide™ PA6-CF is a carbon fiber reinforced nylon (PA6) 3D printing material offering the highest strength, impact resistance and heat deflection of all Polymaker 3D printing materials. More
Raise HyperCore filament concentrates most of the fibres in the centre of the filament to allow higher speed printing, while increasing layer adhesion and giving a great surface finish. More
This wear resistant nozzle by Micro Swiss is the standard size for a range of printers has a 5mm long M6 thread, but has a larger and 0.6mm hole, which it sometimes used for faster printing and with metal and PETG filaments. Total Length 13mm
More
0.2mm Nozzle for Micro Swiss All Metal MK10 Hotend Kit-FFtc
This is Micro Swiss MK10 All Metal Hotend ONLY style nozzle, it will ONLY fit the New MK10 All Metal Hotend. This nozzle has completely different internal dimensions to work with our Micro Swiss thermal barrier tube More
0.3mm Nozzle for Micro Swiss All Metal MK10 Hotend Kit-FFtc
This is Micro Swiss MK10 All Metal Hotend ONLY style nozzle, it will ONLY fit the New MK10 All Metal Hotend. This nozzle has completely different internal dimensions to work with our Micro Swiss thermal barrier tube. More
High Temp Resistant PLA + Black Carbon Fibre - 1.75mm - 500g - UNTIL SOLD OUT
Protopasta Carbon Fiber Composite HTPLA is a combination of milled carbon fibers and high-performance PLA. Resulting 3D prints made with our Carbon Fiber HTPLA are demonstrably more rigid, providing excellent structural strength and layer adhesion with very low warpage. The embedded carbon provides a beautiful matte black finish with a slight sheen, resulting in 3D prints with exceptional accuracy, finish, and performance! More
PolyMaker Glass Fibre PA6 Nylon, Grey, 1.75mm, 150g Sample - UNTIL SOLD OUT
this is a sample coil of 150g only, so you can try a few prints before investing in a 2kg spool.
PolyMide™ PA6-GF is a glass fiber reinforced Nylon (PA6) that offers outstanding mechanical properties, namely, impact strength and stiffness. The material exhibits excellent thermal and mechanical properties without sacrificing the layer adhesion. PolyMide™ PA6-GF can be used to print parts working in a wide temperature range and has been utilized to create custom lab equipment working at temperatures as low as -190°C. More
This wear resistant nozzle by Micro Swiss is the standard size for a range of printers has a 5mm long M6 thread and 0.4mm tip hole. Total Length 13mm. The main hole is for filament with 2.85/3mm diameter or 3mm OD PTFE tube.
0.6mm Nozzle for MicroSwiss All Metal MK10 Hotend Kit
This is Micro Swiss MK10 All Metal Hotend ONLY style nozzle, it will ONLY fit the New MK10 All Metal Hotend. This nozzle has completely different internal dimensions to work with our Micro Swiss thermal barrier tube
More
TwinClad Coated 0.4mm nozzle for Zortrax M200 + UP Plus 2 printers
This nozzle from US firm MicroSwiss fits Zortrax M22, Afinia and UP! style printers, it is made from a 360 brass base material and plated with TwinClad XT coating.
PLA Blend Filament - Carbon Fiber - 2.85mm - 125g Coil - UNTIL SOLD OUT
This amazing filament is a blend of PLA and carbon Fiber by ProtoPasta in the USA. It prints easily at 230-245 degrees on a cold bed. We used glue on a glass bed for our test. More
0.8mm Nozzle for MicroSwiss All Metal MK10 Hotend Kit-FFtc
This is Micro Swiss MK10 All Metal Hotend ONLY style nozzle, it will ONLY fit the New MK10 All Metal Hotend. This nozzle has completely different internal dimensions to work with our Micro Swiss thermal barrier tube
More
PolyMide™ PA6-GF is a glass fiber reinforced Nylon (PA6) that offers outstanding mechanical properties, namely, impact strength and stiffness. The material exhibits excellent thermal and mechanical properties without sacrificing the layer adhesion. PolyMide™ PA6-GF can be used to print parts working in a wide temperature range and has been utilized to create custom lab equipment working at temperatures as low as -190°C. More
PolyMide™ PA6-GF is a glass fiber reinforced Nylon (PA6) that offers outstanding mechanical properties, namely, impact strength and stiffness. The material exhibits excellent thermal and mechanical properties without sacrificing the layer adhesion. PolyMide™ PA6-GF can be used to print parts working in a wide temperature range and has been utilized to create custom lab equipment working at temperatures as low as -190°C. More
PolyMide™ PA6-CF is a carbon fiber reinforced nylon (PA6) 3D printing material offering the highest strength, impact resistance and heat deflection of all Polymaker 3D printing materials. More
1.0mm Nozzle for MicroSwiss All Metal MK10 Hotend Kit-FFtc
This is Micro Swiss MK10 All Metal Hotend ONLY style nozzle, it will ONLY fit the New MK10 All Metal Hotend. This nozzle has completely different internal dimensions to work with our Micro Swiss thermal barrier tube
More
1.2mm Nozzle for MicroSwiss All Metal MK10 Hotend Kit-FFtc
This is Micro Swiss MK10 All Metal Hotend ONLY style nozzle, it will ONLY fit the New MK10 All Metal Hotend. This nozzle has completely different internal dimensions to work with our Micro Swiss thermal barrier tube
More
Raise HyperCore filament concentrates most of the fibres in the centre of the filament to allow higher speed printing, while increasing layer adhesion and giving a great surface finish. More
Raise HyperCore filament concentrates most of the fibres in the centre of the filament to allow higher speed printing, while increasing layer adhesion and giving a great surface finish. More
Raise HyperCore filament concentrates most of the fibres in the centre of the filament to allow higher speed printing, while increasing layer adhesion and giving a great surface finish. More
PLA Blend Filament - 1.75mm - Stainless Steel - 500g Spool - UNTIL SOLD OUT
Proto-pasta Stainless Steel PLA is a dense material that prints as easily as standard PLA but results in heavy prints that can be finished post-print to achieve amazing results. Perfect for jewelry, costumes, props, figurines, crafting, robots, and more!
In filament form, SSPLA is slightly more brittle than standard PLA, and requires extra care when handling.
Processing is comparable to standard PLA (extrudes at 190-240C). No heated bed required. Due to increased brittleness, process may be less consistent on smaller nozzles and/or bowden type machines. More
PLA Blend Filament - Carbon Fiber - 1.75mm - 500g - UNTIL SOLD OUT
This amazing filament is a blend of PLA and carbon Fiber by ProtoPasta in the USA. Will wear nozzle so we advise using a wear resistant nozzle (sold seperately). Produces impressively strong models with minimum fuss and difficulty. More
PLA Blend Filament - Carbon Fiber - 1.75mm - 50g Sample Coil - UNTIL SOLD OUT
This amazing filament is a blend of PLA and carbon Fiber by ProtoPasta in the USA. It prints easily at 230-245 degrees on a cold bed. We used glue on a glass bed for our test. Tendancy to leave small balls/pimples on surface which easily clean up. Will wear nozzle so we advise using a wear resistant nozzle (sold seperately). Produces impressively strong models with minimum fuss and difficulty. More
This wear resistant nozzle by Micro Swiss is the standard size for a range of printers
It has a Wear Resistant High Lubricity TwinClad XT Coating this makes it a excellent choice when printing with abrasive/wearing material such as Bronze, Copper, Alumininium or Carbon Fiber filament.
More
This wear resistant nozzle by AVN/Micro Swiss is the standard size for a range of printers
It has a Wear Resistant High Lubricity TwinClad XT Coating this makes it a excellent choice when printing with abrasive/wearing material such as Bronze, Copper, Alumininium or Carbon Fiber filament.
More
Sydney - Kingsgrove, NSW
Melbourne - Clayton, VIC
