FlashForge Bed Level Sensor Board (Guider / Finder / Inventor 2)
This is the sensor that detects the bed on a Guider, Guider2, Finder and Inventor 2. It is screwed onto the sensor arm, which is then attached the the motor (both sold seperately). It can get broken if level is very out or in cases of extreem print fails. BE AWARE older editionsl of original Guider use a square board, not this part-see PTsensorFF. More
0.4mm Nozzle for FlashForge All Metal Hot Ends - FFam
When the FlashForge Guider2S switched over to a high-temperature hot end, it came with a different nozzle and barrel/heatbreak (with red nozzle duct) More
FlashForge Thermocoupler - Short with Molex connector
Genuine FlashForge thermocoupler with 11cm lead length and Molex connector for the Finder, Inventor2 and Guider Series which have a terminal board on the extruder carriage. More
Teflon tube for Flashforge Dual Extruder Barrel-FFD
This short piece of Teflon tubing is for lining the barrel on the Flashforge Dreamer, Creator Pro, Creator Pro2 (IDEX) and Inventor. Over time (and with high temperatures), they will need replacing More
MicroSwiss All Metal Hotend Kit for FlashForge Finder, Guider, Inventor 2/2S/2SE-FFtc
Genuine Micro-Swiss all metal hotend upgrade for the FlashForge Guider, Guider 2
Finder, FinderPlus and Inventor2 recomend - ptKitMK10TC3
Comes with 0.4mm nozzle, range of other sizes available More
0.4mm Nozzle for FlashForge Creator3v2 (2020 model)
Genuine FlashForge standard nozzle for the updated Creator3. WARNING Requires teflon tube that is included and is approx 42mm long and inserts in top half More
0.4mm Nozzle for MK10 Micro Swiss All Metal MK10 Hotend Kit-FFtc
This is Micro Swiss MK10 All Metal Hotend ONLY style nozzle, it will ONLY fit the New MK10 All Metal Hotend. This nozzle has completely different internal dimensions to work with our Micro Swiss thermal barrier tube More
All Metal Hot End Assembly for FlashForge Inventor 2/2SE-FFtc
This is a slot in replacement for FlashForge machines with a cylindrical heatsink and 24V heater cartridge. This edition has the shorter heat sink (see more information page) More
This Arm pivots down on the Guider 2, with the level sensor screwed on to it.
The arm attaches to the Bed sensor motor.
DOES NOT WORK/FIT ON A GUIDER 1, Inventor 2/2SE and Finder, see ptSensorBedArmFF. This arm differs from that arm are in that it has a cut out in the top right of the spoon. More
Genuine Micro-Swiss all metal hotend upgrade for MK10 style extruders.
MK10 Extruders most notibly used on the FlashForge Dreamer, Inventor1 and Creator Pro 2016 and Dremel Idea Builder. It also fits the Wanhao i3 and Cocoon More
Capricorn Tube for Creator Pro 2 Extruder Barrel-CP2
Regular PTFE barrel liners blacken and shrink after a couple of hundred hours printing, especially if printing at higher temepratures.
The Capricorn PTFE tube is modified to better withstand high temperatures, extending life More
Extruder Turbo Fan for Flashforge Guider 2/Inv SE (3 pin connector, 2 cables)
Genuine Flashforge extruder fan for the Guider 2 and SE, has a 3 pin connector with 2 cables only. NOTE: flashforge Dreamer ones have 2 pin connectors, Guider 2s has 3 pin connector with 3 cables. SEE SUPPORT NOTES for more info. More
Machined Lever for Creator Pro - Right Side and Wanhao i3
This is a replacement lever and extruder plate for Dual Extruders (Right Side Only).
Lever and plate are CNC machined from 6061 billet aluminum, with weight reduction features.
Also suitable for the Wanhao i3
More
The carbon in these air filters is designed to absorb chemicals from the air, so it is important that they be replaced regularly (~ every 3 months) More
0.4mm Toughened Nozzle for FlashForge All Metal Hot Ends - FFam
When the FlashForge Guider2S switched over to a high-temperature hot end, it came with a different nozzle and barrel/heatbreak (with red nozzle duct) More
Teflon Tube for FlashForge Creator Pro 2 Extruder Barrel-CP2
Genuine FlashForge replacement part to line the barrel/throat/heatbreak in your extruder.
The tube deteriorates after ~400 hours of printing, depending on your printing temperatures and materials More
Genuine FlashForge replacement part inclides the metal housing + heated bed plate, ceramic underlay and glass bed. Screws for leveling attached but does not include springs and thumbscrew knobs More
The short barrel / throat / heatbreak for the FlashForge High Temperature hotend, found on leter version of the FlashForge Guider2s (with a red nozzle duct) More
Hardened 0.6mm Nozzle for FlashForge Creator3v2 (2020 model)
Genuine FlashForge replacement nozzle for the updated Creator3. WARNING Requires teflon tube that is included and is approx 42mm long and inserts in top half
Note: Steel Nozzle shown in photo More
This heatsink is 40x40mm with mounting holes and removed fins ready for fitting to your Nema17 based extruder. Actually a genuine part for the FlashForge Dreamer series, but will fit many other printers as well More
0.2mm Nozzle for Micro Swiss All Metal MK10 Hotend Kit-FFtc
This is Micro Swiss MK10 All Metal Hotend ONLY style nozzle, it will ONLY fit the New MK10 All Metal Hotend. This nozzle has completely different internal dimensions to work with our Micro Swiss thermal barrier tube More
0.3mm Nozzle for Micro Swiss All Metal MK10 Hotend Kit-FFtc
This is Micro Swiss MK10 All Metal Hotend ONLY style nozzle, it will ONLY fit the New MK10 All Metal Hotend. This nozzle has completely different internal dimensions to work with our Micro Swiss thermal barrier tube. More
BuildTak FlexiPlate System for FlashForge Guider 2 / 2S
BuildTak is proud to announce the latest addition to their line of 3D printing accessories – the BuildTak FlexPlate System!
As a company dedicated to making the 3D printing experience as easy as possible, this three-part system was developed specifically to eliminate the hassle of print removal More
This endstop cable is for FlashForge Dreamer series of 3D Printers. One spare comes with the printer. It will fit either the X, Y or Z endstop boards (endstop board sold separately) More
FlashForge Thermocoupler - Short for Dreamer-FFD > UNTIL SOLD OUT
Discontinued - Use ptThermoFFshCon and cut the connector off!
Genuine FlashForge thermocoupler
M4 brass fitting at sensing end (Note: our other thermocouplers and heater blocks are all M3)
Crimped terminals at motherboard end
~11cm lead length - Suited to the FlashForge Dreamer which has a terminal board on the extruder carriage More
0.6mm Nozzle for MicroSwiss All Metal MK10 Hotend Kit
This is Micro Swiss MK10 All Metal Hotend ONLY style nozzle, it will ONLY fit the New MK10 All Metal Hotend. This nozzle has completely different internal dimensions to work with our Micro Swiss thermal barrier tube
More
Flat Ribbon Cable for FlashForge Dreamer/Inventor 1 - 45cm
This is a genuine FlashForge Ribbon Cable that runs from the Processor Board to the Driver Board. It is also a compatible replacement for the cable from the LCD screen on Dreamer and Inventor 1 (excess length can easily tuck away). More
This genuine FlashForge part is for the right hand side of the gantry - it holds the two rods which the extruder carriage slides up and down plus the stepper motor More
This Arm pivots down on the Guider, Inventor 2/2SE and Finder with the level sensor screwed on to it.
The arm attaches to the Bed sensor motor.
DOES NOT WORK/FIT ON A GUIDER 2, see ptSensorBedArmFFG2. This arm differs from that arm as the spoon area is squared. The Guider 2 one has a cut out in the top right of the spoon. More
0.8mm Nozzle for MicroSwiss All Metal MK10 Hotend Kit-FFtc
This is Micro Swiss MK10 All Metal Hotend ONLY style nozzle, it will ONLY fit the New MK10 All Metal Hotend. This nozzle has completely different internal dimensions to work with our Micro Swiss thermal barrier tube
More
Machined Lever Assembly for Finder, Guider and Creator Pro - Left Side
This is a replacement lever and extruder plate for Dual Extruders (Left Side Only).
Lever and plate are CNC machined from 6061 billet aluminum, with weight reduction features.
More
Power Supply for a range of FlashForge Printers, including the Dreamer, Inventor (1), Creator Pro and Creator Pro 2 (IDEX)
Genuine part supplied by Flashforge More
This flight ready, rugged road case is designed to neatly store your Flashforge Finder, Inventor 2 or Special Edition 3D Printer, with a rear storage section for Filament, spare parts and power supply. It is on lockable casters for easy moving. More
Spool Holder for 600g Spools (compatible with Creator Pro, Guider and Raise)
This spool holder clips into the existing spool holder bracket on a creator Pro, Guider or Raise and is the correct size for 600g spools (spools with a 2cm center hole) More
Machined Lever Assembly for Finder, Guider and Creator Pro - Left Side
This is a replacement lever and extruder plate for Dual Extruders (Left Side Only).
Lever and plate are CNC machined from 6061 billet aluminum, with weight reduction features.
More
1.0mm Nozzle for MicroSwiss All Metal MK10 Hotend Kit-FFtc
This is Micro Swiss MK10 All Metal Hotend ONLY style nozzle, it will ONLY fit the New MK10 All Metal Hotend. This nozzle has completely different internal dimensions to work with our Micro Swiss thermal barrier tube
More
1.2mm Nozzle for MicroSwiss All Metal MK10 Hotend Kit-FFtc
This is Micro Swiss MK10 All Metal Hotend ONLY style nozzle, it will ONLY fit the New MK10 All Metal Hotend. This nozzle has completely different internal dimensions to work with our Micro Swiss thermal barrier tube
More
0.3mm Brass Nozzle for FlashForge HighTemp Hot Ends - FFam
When the FlashForge Guider2S switched over to a high-temperature hot end, it came with a different nozzle with a longer thread and barrel/heatbreak (with red nozzle duct) More
0.6mm Brass Nozzle for FlashForge All Metal Hot Ends - FFam
When the FlashForge Guider2S switched over to a high-temperature hot end, it came with a different nozzle and barrel/heatbreak (with red nozzle duct) More
Genuine FlashForge replacement part for Guider 2v2 2020 machines ONLY. Please check specification tab under more info for details. Please compare specifications tab to marking on your belts before ordering. More
FlashForge Finder + Inventor 2 Model Cooling Duct - Upper
The cooling duct cools the material as soon as it leaves the nozzle giving great print quality and overhangs.
Supplied in 2 pieces - This is the upper half More
FlashForge Finder + Inventor 2 Model Cooling Duct - Lower
The cooling duct cools the material as soon as it leaves the nozzle giving great print quality and overhangs.
Supplied in 2 pieces - This is the lower half More
0.8mm Nozzle for FlashForge Creator3v2 (2020 model)
Genuine FlashForge replacement nozzle for the updated Creator3. WARNING Requires teflon tube that is included and is approx 42mm long and inserts in top half More
Dreamer / Inventor / CreatorPro Blue Print Bed Tape, 23x15cm
This is a genuine FlashForge replacement sheet for the FlashForge Dreamer, Inventor1, Creator Pro 2016 (v5) and Creator Pro2 (IDEX) printing bed.
It is similar to BuildTak but with more texture on the surface, and a very aggressive glue that does not like to dissolve
This is a genuine FlashForge replacement sheet for the FlashForge Guider2 printing bed.
It is similar to BuildTak, but with more surface texture, and can be cut down with scissors or a knife and used on other machines with a differently sized bed More
This is a genuine FlashForge replacement part for the FlashForge Finder
It clips in and out of the plastic holder which slides in and out of the machine to remove prints More
Sydney - Kingsgrove, NSW
Melbourne - Clayton, VIC
