Tested on Blue tape and straight on glass (both cold) with excellet adhesion.
Extrusion molding grade; with special UV stabilizers; very good hydrolysis and microbial resistance;
good low-temperature flexibility;
- Will spiderweb, so choose model well.
- Turn filament fan off during early layers, then print like you would PLA.
- We recommend raising the print temp. slightly compared to regular PLA and reduce the print speed to around 40mm/s to help the filament to just fall out of the nozzle rather than be pushed by the feeder
- Melting Point 190-250 °C
Material - TPU (Thermo Plastic Urethane) by Bayer Science
Diameter: 1.75mm (+/- 0.04mm)
Weight: Aprox. 600g of filament, plus spool and box
Melting Point: 190-250 °C - Best on Inventor2SE at 220°
Abrasive: No
Build Surface: Buildtak, glass (recommend hairspray or 3D Lac. Cold bed great.
Source Material Properties(Manufacturers Figures) - When printed, values will depend on your printer and settings
- Shore Hardness, Method A: Typical Value 95, Range 92-96 (to ISO 868)
- Shore Hardness, Method D: Typical Value: 48, (to ISO 868)
- Ultimate Tensile Strength: 50Mpa (Test DIN 53504 Condition 200mm/min)
- Strain at Break: 420% (Test DIN 53504, Condition 200mm/min)
- Stress at 100% Strain: 12/5 MPa (DIN 53504, condition 200mm/min)
- Stress at 300% Strain: 30.0MPa (DIN 53504, 200mm/min)
- Abrasion Resistance: 45mm3 (ISO 4649, method B)
- Tear Propagation Resistance: 130 kN/m (ISO 34-1, 500mm/min)
- Density: 1144 kg/m3 (ISO 1183-1)
- Maximum Drying Temperature: 110 °C
PACKAGING
Vacuumed in heavy duty bag to help with proper storage, then protected by a cardboard box.
Product Dimensions: 178x178x53mm
Next >
We have printed a lot with this material on the Flashforge Dreamer. Settings and info you may find helpful:
Bed Temp: We heat the bed to 50 degrees, unless twin extruding with ABS see below.
Resolution : 200 - 300 micron
Print Speed: 30 mm/second
Temperature: 230 degrees
Nozzle fan: ON (we use the left extruder on the dreamer and tell the default it is PLA so this turns on.
Two Materials: We have printed Flex-PLA and Flex-ABS Both stick/fuse well together. In both cases we use the plastic as the raft. With ABS we raise the bed temp to 110, however also found the higher heat did effect print quality of the flex (perhaps as the filament fan is also turned off).
General Note: Flex is very susceptible to stringy webs between walls (called spider webbing). Reducing temperature defiantly helps, as does slowing print speed. It is interesting that in the heated chamber of ABS printing this is much less, but the quality of the overall flex print is also more poor.
Bilby 3D provides a 1 month Australian, back-to-base warranty of this product (Terms and conditions) For technical support of this product please read our knowledge bank or log a ticket
10% Bulk Discount available; Order 10 or more filament at once, Prepay for your order, Phone 1800-847-333 to order. Conditions apply.
Spectrum S-Flex 90A is a filament designed for 3D printing which enables you to manufacture flexible items in a much simpler manner than with other materials of this type. The optimised composition of the material provides for good adhesion both between layers and between the printed item and the build platform.
Buy Now
Spectrum S-Flex 90A - 1.75mm - Lion Orange - 500g
Spectrum S-Flex 90A is a filament designed for 3D printing which enables you to manufacture flexible items in a much simpler manner than with other materials of this type. The optimised composition of the material provides for good adhesion both between layers and between the printed item and the build platform.
All prices are in Australian Dollars and include GST. Standard Postage & Handling with Australia is $12 flat rate, free for orders over $350. Express Post starts at $15
Sydney - Kingsgrove, NSW
Melbourne - Clayton, VIC
