BuildTak PEI Bed Tape for Raise Pro2, N2 - 332x340mm
Introducing the BuildTak Polyetherimide (PEI) Print Surface. Now you can choose the print surface best-suited to the material being printed.
Slightly less model adhesion than the original BuildTak, it is recommended where consistant prints are required, but a bit easier to remove the print, such as large and PETG prints
FeaturesSpecsSupport
Manufactured in the US to ensure consistent quality and composition, BuildTak Polyetherimide (PEI) build surfaces are made from premium Ultem 1000 PEI equipped with the no-cleanup BuildTak Original adhesive.
A comparable alternative to the BuildTak Original 3d printing surface, BuildTak PEI exhibits slightly different adhesion and release properties which vary depending on the material being printed.
In general, BuildTak PEI offers easier release of finished prints while BuildTak Original offers a stronger hold during printing.
Paired with the BuildTak FlexPlate System, you can keep multiple FlexPlates on-hand to easily swap out between the BuildTak Original and BuildTak PEI print surfaces, depending on the material being printed.
For example, Polycarbonate requires BuildTak’s extra-strong hold to finish prints successfully, while PEI should be used for PETG because of its easier release.
PLUS! BuildTak PEI and BuildTak Original are both 0.25mm (0.010in) so no need to re-level when swapping!
Next >
Genuine BuildTak PEI Build Surface
- 340mm wide
- 332mm deep
- 0.254mm thick - same as Original BuildTak
- BuildTak no/low clean-up adhesive
Product Dimensions: 332 x 340 x 0.25 mm
Next >
This product has no specific warranty. Bilby 3D will honor obligations under Australia Consumer Guarantee regulations if and where they apply to this product
BuildTak Bed Tape for Raise3D Pro2, N2-S, N2, N2 Plus
This is the original tape fitted to your Raise 3D print bed
Size: 332 x 340mm
Buy Now
Buildtak Spatula
With a right angled handle and a blade that is very thin at the front edge, this is a great tool for getting those really well stuck prints off the bed!
Buy Now
BuildTak Spatula - Long Version
This longer version of the popular BuildTak Spatula is designed for getting those larger prints off the bed!
The BuildTak Spatula is a removal tool designed and developed specifically for 3D Printing. No more using a tool adapted from some other purpose. This awesome new tool features a stainless steel blade with a thin yet rigid front edge for getting under prints. The handle is ergonomic and uses a non-slip rubber grip.
Buy Now
Rapid Tac - Bed Tape Application Fluid - 110ml
Rapid Tac - Cleaner and Application Fluid. 4oz / 110g spray bottle
Use with paper towel (no cloths) to clean your bed and apply bed tape easily, without any bubbles.
The bottle says: For wet application of decals, graphics and film. Formulated for premium, cast film applications in all climates
Eliminate bubbles and wrinkles
Reposition while applying
Effective in all weather conditions
Buy Now
BuildTak Nylon+ Tape for Raise3D N2 / Pro2 Series - 340 x 330mm
Manufactured in the USA to ensure consistent quality and composition, BuildTak Nyon+ build surfaces come with the no-cleanup BuildTak Original adhesive.
Buy Now
B3D Tape for Raise3D N2 / Pro2 Series - 340 x 330mm - by BuildTak
Custom printed for Bilby3D by BuildTak in the USA, this tape fit not just the Raise3D N2 and Pro2 series, but also many other printer of this size
All prices are in Australian Dollars and include GST. Standard Postage & Handling with Australia is $12 flat rate, free for orders over $350. Express Post starts at $15
Sydney - Kingsgrove, NSW
Melbourne - Clayton, VIC
