Genuine FlashForge thermocoupler
100cm lead length - Suited to the Creator Pro and earlier
FeaturesSpecsSupport
M4 brass fitting at sensing end (Note: our other thermocouplers and heater blocks are all M3)
Crimped terminals at motherboard end
Next >
- 1m lead length
- Brass mounting plug with M4 Thread at heaterblock end
- Crimped terminals at motherboard end
Product Dimensions: 1180 x 6 x 6mm
Next >
This product has no specific warranty. Bilby 3D will honor obligations under Australia Consumer Guarantee regulations if and where they apply to this product
0.4mm Genuine FlashForge Nozzle - M7 Thread for MK10 Extruder-FFptfe
This is a genuine nozzle from FlashForge. M7 tread.
Buy Now
Extruder Heatsink for Guider 2S - High Temperature Version - FFam
Genuine FlashForge replacement part
For the High-Temp (300°C) hotend with the red cooling duct
Buy Now
Heater Cartridge for the Guider 1/Finder (12V, 18.5mm long)
Genuine FlashForge replacement part for the Guider 1 and the Finder machines, NOT THE GUIDER 2 or Inventor machines-see specs tab
Buy Now
Flashforge Barrel for Dreamer / Creator Pro / Inventor 1 - FFptfe
Genuine FlashForge barrel. It has a smooth outer tube with flats for holding with a spanner or pliers and a threaded end
Buy Now
Barrel for Flashforge Guider / Finder - FFptfe
Threaded metal tube that runs between the heater block and the circular heatsink in the extruder
Buy Now
0.6mm Brass Nozzle for FlashForge All Metal Hot Ends - FFam
When the FlashForge Guider2S switched over to a high-temperature hot end, it came with a different nozzle and barrel/heatbreak (with red nozzle duct)
Buy Now
FlashForge Nozzle Set for Guider 2 High-Temp Hotends - FFam
Nozzle set with toughened drive gear and tools for the Guider2S with a high-temperature hotend. This will have a RED nozzle duct
Buy Now
High Temp Barrel for FlashForge Guider2S - FFam
The short barrel / throat / heatbreak for the FlashForge High Temperature hotend, found on leter version of the FlashForge Guider2s (with a red nozzle duct)
Buy Now
FlashForge Heater Cartridge for the CreatorPro2-CP2
Genuine FlashForge spare extruder heater for the Creator Pro 2.
Fits both left and right extruders.
Buy Now
Heater Cartridge for Dreamer and Inventor 1 only-FFD > UNTIL SOLD OUT
Genuine Spare part for FlashForge Dreamer and Inventor 1 only heater cartridge.
Note : Flashforge CreatorPro cable is different (see image 3, ptHeatCart4024)
Flashforge Finder, Guider (1 and 2) and Inventor2 also have a short heater. This is not compatible
Buy Now
Capricorn Teflon tube for Flashforge Single Extruder Barrel - FFptfe
This short piece of Teflon tubing is for lining the barrel on the Flashforge Guider, Guider2, Finder, Finder Plus and Inventor 2
Made from Capricorn Tubing, it is higher lubricity and more resistant to the high temperatures experiences in a hot end
Buy Now
0.4mm Toughened Nozzle for FlashForge All Metal Hot Ends - FFam
When the FlashForge Guider2S switched over to a high-temperature hot end, it came with a different nozzle and barrel/heatbreak (with red nozzle duct)
Buy Now
Heater Block for FlashForge Creator Pro 2 (IDEX)-CP2
Genuine FlashForge Heat block for the Creator Pro 2 (IDEX) - Left and Right identical
Buy Now
Heater Block for FlashForge Guider 2S HT - FFam
Genuine FlashForge spare part
this heater block suits those G2S with the High-Temp (300°C) hotends
Does Not include Grub screw or Bolt
Buy Now
FlashForge Hot End Assembly for Guider2s - 300°C - FFam
Genuine Flashforge HotEnd Assembly for the Guider2S
With a brass 0.4mm nozzle and is rated to 300 °C
Buy Now
All Metal Hot End Assembly for FlashForge Inventor 2/2SE-FFtc
This is a slot in replacement for FlashForge machines with a cylindrical heatsink and 24V heater cartridge. This edition has the shorter heat sink (see more information page)
Buy Now
Teflon Tube for FlashForge Guider 2 - High Temp HotEnd - FFam
26mm length to suit ptHotEndAssFFg2HT - made from Capricorn PTFE Tube
Buy Now
0.4mm Nozzle for FlashForge All Metal Hot Ends - FFam
When the FlashForge Guider2S switched over to a high-temperature hot end, it came with a different nozzle and barrel/heatbreak (with red nozzle duct)
Buy Now
All Metal Hot End Assembly for FlashForge Guider 2 / 2S-FFtc
This is a slot in replacement for FlashForge machines with a cylindrical heatsink and 24V heater cartridge
Buy Now
FlashForge Thermocoupler - Short with Molex connector
Genuine FlashForge thermocoupler with 11cm lead length and Molex connector for the Finder, Inventor2 and Guider Series which have a terminal board on the extruder carriage.
Buy Now
Teflon tube for Flashforge Single Extruder Barrel - FFptfe
This short piece of Teflon tubing is for lining the barrel on the Flashforge Guider, Guider2, Finder, Finder Plus and Inventor 2
All prices are in Australian Dollars and include GST. Standard Postage & Handling with Australia is $12 flat rate, free for orders over $350. Express Post starts at $15
Sydney - Kingsgrove, NSW
Melbourne - Clayton, VIC
