Prices + Stock updated 9 Mar @ 13:04
Heater Block for the FlashForge Finder, Guider, Inventor 2-FFptfe-FFtc
Genuine heater block for the FlashForge Finder series, Guider Series and Inventor 2
Features
Specs
Support
Has a M7 tapped (barrel threaded) and recessed hole for the barrel, and nozzle most other printers are M6!
Has an M3 drilled and tapped holes for the thermocoupler (temperature sensor) (note that dreamer Inventor and Creator pro have M4)
Next >
- Block Dimensions: 17.5 x 15mm, 13mm tall
- Thermo connector thread M3 screw
- Takes a MK10 Nozzle and barrel (7mm)
- Takes a 6-6.35mm heater catridge secured with M4 grub screw
Note re Cocoon and Wanhao machines: They use an M7 threaded barrel and nozzle, with M3 grub screw for heater cartridge and thermo connection; so this is the best heater block to buy but is smaller in size, your heater cartridge may extend too long.
Product Dimensions: 17.5x15x13mm
Next >
This product has no specific warranty. Bilby 3D will honor obligations under Australia Consumer Guarantee regulations if and where they apply to this product
Related Products:
Buy Now
Silicone Sock Heater Block Cover for Inventor2 / Guider2 / Finder-FFtc-FFptfe
This cover goes over the heater block to keep the heat where it is meant to be.
Buy Now
0.4mm Genuine FlashForge Nozzle - M7 Thread for MK10 Extruder-FFptfe
This is a genuine nozzle from FlashForge. M7 tread.
Buy Now
Flashforge Barrel for Dreamer / Creator Pro / Inventor 1 - FFptfe
Genuine FlashForge barrel. It has a smooth outer tube with flats for holding with a spanner or pliers and a threaded end
Buy Now
Teflon tube for Flashforge Single Extruder Barrel - FFptfe
This short piece of Teflon tubing is for lining the barrel on the Flashforge Guider, Guider2, Finder, Finder Plus and Inventor 2
Buy Now
Capricorn Teflon tube for Flashforge Single Extruder Barrel - FFptfe
This short piece of Teflon tubing is for lining the barrel on the Flashforge Guider, Guider2, Finder, Finder Plus and Inventor 2
Made from Capricorn XS Tubing, it is higher lubricity and more resistant to the high temperatures experiences in a hot end
Buy Now
Inventor 2SE - 6 Month Maintenance Kit
Contains the common consumables and tools you need after 6 months to keep your FlashForge Inventor 2S/SE in top working order
Buy Now
All Metal Hotend with Cooling Block for Wanhao i3
Micro Swiss All Metal Hotend kit with redesigned cooling block for Wanhao i3, Wanhao i3 Plus and all other i3 clones with the following improvements:
- Slotted Clamping system
- No set screw to ding and damage thermal tube
- Significantly better heat transfer (this is a big one!!!)
- Easier disassemble and adjustments
- Precise control on bore diameter
Buy Now
All Metal Hot End for FlashForge Inventor 2/2S/SE & Guider 2/2S
This hotend fits several FlashForge 3D Printers
Buy Now
FlashForge Thermocoupler - Short with Molex connector
Genuine FlashForge thermocoupler with 11cm lead length and Molex connector for the Finder, Inventor2 and Guider Series which have a terminal board on the extruder carriage.
All prices are in Australian Dollars and include GST. Standard Postage & Handling with Australia is $12 flat rate, free for orders over $350. Express Post starts at $15
Sydney - Kingsgrove, NSW
Melbourne - Clayton, VIC
