Rapid Tac - Cleaner and Application Fluid. 4oz / 110g spray bottle
Use with paper towel (no cloths) to clean your bed and apply bed tape easily, without any bubbles.
The bottle says: For wet application of decals, graphics and film. Formulated for premium, cast film applications in all climates
Eliminate bubbles and wrinkles
Reposition while applying
Effective in all weather conditions
FeaturesSpecsSupport
RapidTac is NOT required to install a BuildTak sheet, but it is recommended for BuildTak users installing sheets 300x300mm or larger. Some customers have reported that larger BuildTak sheets can be more difficult to apply without accidentally trapping air bubbles, which are almost impossible to remove once a sheet is installed. Because larger sheets are more expensive to replace if installed improperly, RapidTac is a good investment to make sure you get the installation right every time. One 4oz bottle will last for about a dozen installations or more (depending on sheet size). we now use Rapid Tac for installation of all BuildTak sheets 300 x 300mm or larger.
Please note that installations using RapidTac require 24 hours to dry before printing, after which your BuildTak sheet will function as normal. (Do not attempt to heat your bed to speed up the drying process; This may cause air bubbles to form.)
The step-by-step instructions are included below for easy reference:
Before installing a new BuildTak sheet, clean your bed thoroughly with rubbing alcohol and ensure it is completely dry
Apply RapidTac generously to your print bed, ensuring that all areas are thoroughly soaked (no dry patches)
After removing the white liner, lightly place the BuildTak sheet onto your bed. Agitate slightly to get the adhesive side lubricated, then move into position. (Don’t worry if you get liquid on the BuildTak surface – it can be cleaned later with 70% rubbing alcohol.)
Once in place, use a decal applicator to squeegee out excess liquid toward the edge of the BuildTak sheet, wiping clean with a rag or paper towel. You’ll know you’ve finished removing any excess RapidTac when you no longer see liquid bubbling out from the edge of the sheet after squeegeeing
Wipe down any remaining liquid and allow 24 hours to dry. Before printing, clean the BuildTak sheet with 70% rubbing alcohol to ensure no RapidTac residue is left behind
Next >
Product Dimensions: 150 x 40 x 40mm
Next >
This product has no specific warranty. Bilby 3D will honor obligations under Australia Consumer Guarantee regulations if and where they apply to this product
Material Safety Data Sheet
With a right angled handle and a blade that is very thin at the front edge, this is a great tool for getting those really well stuck prints off the bed!
Buy Now
BuildTak Spatula - Long Version
This longer version of the popular BuildTak Spatula is designed for getting those larger prints off the bed!
The BuildTak Spatula is a removal tool designed and developed specifically for 3D Printing. No more using a tool adapted from some other purpose. This awesome new tool features a stainless steel blade with a thin yet rigid front edge for getting under prints. The handle is ergonomic and uses a non-slip rubber grip.
Buy Now
B3D Tape for Raise3D N2 / Pro2 Series - 340 x 330mm - by BuildTak
Custom printed for Bilby3D by BuildTak in the USA, this tape fit not just the Raise3D N2 and Pro2 series, but also many other printer of this size
Buy Now
BuildTak Print Bed Tape 40x40 cm
This amazing build tape is a special plastic (self adhesive) surface that is stronger and better than old tapes(such as Kapton and Blue Tape), and holds objects on the bed so well. It also lasts significantly longer.
Buy Now
BuildTak Print Bed Tape, 609x609mm
Genuine BuildTak build tape from the USA. 609 x 609mm size
Buy Now
BuildTak (Z18), 30x30cm
The ideal build surface designed just for 3D printers - near smooth surface wwith easy to remove adhesive
Buy Now
Modix3D PEI Tape - 465x465mm
Modix Genuine Spare Part. Designed to cover the bed of the Modix Big-40, but can be cut down to size
Buy Now
Modix3D PEI Tape - 1075x355mm
Single spare PEI sheet at size of 1075x355mm covering a THIRD of the BIG-Meter bed plate. Please order 3 pcs in order to cover the entire bed plate.
Buy Now
BuildTak PEI Bed Tape for Guider2 Series - 260x305mm
Introducing the BuildTak Polyetherimide (PEI) Print Surface. Now you can choose the print surface best-suited to the material being printed.
Slightly less model adhesion than the original BuildTak, it is recommended where consistant prints are required, but a bit easier to remove the print, such as large and PETG prints
Buy Now
Plastic Scraper with soft edge
This plastic scraper is ideal for smoothing tape onto your priter bed, and helping to remove prints and waste from your bed. One edge is sharp, the other has a soft fabric glued on (similar to loop velcro)
Buy Now
BuildTak PEI Bed Tape for Raise Pro2, N2 - 332x340mm
Introducing the BuildTak Polyetherimide (PEI) Print Surface. Now you can choose the print surface best-suited to the material being printed.
Slightly less model adhesion than the original BuildTak, it is recommended where consistant prints are required, but a bit easier to remove the print, such as large and PETG prints
All prices are in Australian Dollars and include GST. Standard Postage & Handling with Australia is $12 flat rate, free for orders over $350. Express Post starts at $15
Sydney - Kingsgrove, NSW
Melbourne - Clayton, VIC
