Prices + Stock updated 9 Mar @ 13:04
Hot End - E3D v6 clone - 1.75mm Filament, 0.4mm nozzle
This complete hot end is based on the All-Metal J-Head design as modified by E3D (V6). Includes everything you need, hot-end wise for 1.75mm filament
Features
Specs
Support
Includes:
- 30mm 12V Fan and Shroud (150mm leads with connector)
- Tube fitting (great for bowden tube setups), can be removed
- Standard Groove Mount (6mm slot)
- Finned Aluminium upper barrel with stainless steel lower. All metal, no PTFE liner for long life at higher temperatures
- Heater block
- Thermistor
- Heater Cartridge (12V)
- Copper Nozzle (0.4mm hole)
Next >
- Length: Nozzle tip to load point - 75mm
- Nozzle Size: 0.4mm
- Filament Size: 1.75mm
- Heater Cartridge: 12V, 40W with 1m lead (raw ends)
- Thermistor: 100K NTC B 3950 +-1%, 1m long leads (2 pin connector)
- Fan is 30 X 30mm
Note: Due to the size of the fins, this hot end will not mount in our Bulldog Extruder without cutting down the top fins
NOTE - if you need to replace ther Thermistor see product code ptThermCable2
If you need to replace the Heater cartridge see ptheatcart1240
Product Dimensions: 80 x 40 x 30mm
Next >
This product has no specific warranty. Bilby 3D will honor obligations under Australia Consumer Guarantee regulations if and where they apply to this product
Related Products:
Buy Now
Barrel for E3D v6 Hot End
This is a replacement part for the E3D v6 clone hotend - All Metal
Buy Now
Hot End - E3D v6 clone - 1.75mm Filament, 0.4mm nozzle - Direct Drive
This complete hot end is based on the J-Head design as modified by E3D (V6). Includes everything you need, hot-end wise for 1.75mm filament.Note this is a PTFE lined system
Designed for extruders using direct drive filament feeding (2mm hole at top)
Buy Now
0.4mm Nozzle - M6 Thread for E3D Hotend - TwinClad - 1.75mm Filament
Nozzle for the E3D Hotend with a Wear Resistant Twin Clad coating for long life
Buy Now
0.4mm Nozzle - M6 Thread for E3D Hotend - Brass - 1.75mm Filament
Brass nozzle for the E3D v5/6 hotend
Buy Now
0.2mm Nozzle - M6 Thread for E3D hotend, 1.75mm Filament, Brass
Brass nozzle for the E3D v5/6 hotend
Buy Now
Heater Cartridge - 40W 24V
This ceramic core heater cartridge has a variety of heating possibilities from hot ends/ extruders to heated beds.
Buy Now
Fan 30mm, 24V DC
Aftermarket 30mm fan, not for use on Flashforge Guider - see specs
Buy Now
30mm fan for the FlashForge Guider 2
Replacement Extruder side fan for the Guider2
Buy Now
0.3mm Nozzle - M6 Thread for E3D Hotend - Brass - 1.75mm Filament
Brass nozzle for the E3D v5/6 hotend
Buy Now
0.5mm Nozzle - M6 Thread for E3D Hotend - Brass - 1.75mm Filament
Brass nozzle for the E3D v5/6 hotend
Buy Now
Stainless Twin Clad Coated Barrel for E3D v6 Hot End - 1.75mm
This heat break is a direct replacement for use in E3D v6 1.75mm hot ends.
Buy Now
0.2mm Nozzle - M6 Thread for E3D hotend, 1.75mm Filament, Stainless Steel
Brass nozzle for the E3D v5/6 hotend
Buy Now
0.6mm Nozzle - M6 Thread for E3D v5/v6 hotend - Brass - 1.75mm Filament
0.6mm Nozzle for E3D v5/v6 hotend, 1.75mm filament, brass
Buy Now
0.8mm Nozzle - M6 Thread for E3D v5/v6 hotend - Brass - 1.75mm filament
0.8mm Nozzle for E3D v5/v6 hotend, 1.75mm filament, brass
Buy Now
0.6mm Nozzle - Hardened M6 Thread for E3D v5/v6 hotend - 1.75mm Filament
0.6mm Nozzle for E3D v5/v6 hotend, 1.75mm filament, Hardened
Buy Now
0.4mm Nozzle - M6 Thread for E3D Hotend - Stainless Steel - 1.75mm Filament
This nozzle for the E3D V5/6 Hotend is Stainless Steel for extra long life
All prices are in Australian Dollars and include GST. Standard Postage & Handling with Australia is $12 flat rate, free for orders over $350. Express Post starts at $15
Sydney - Kingsgrove, NSW
Melbourne - Clayton, VIC
