MakerBot Labs GEN 2 Experimental Extruder for Method + Method X
This extruder for the Makerbot / Ultimaker Method and MethodX allows you to set a wide variety of settings for materials not covered by their other extruders.
Makerbot Nylon (PA 6/66) Carbon Fibre has the highest peak performance in all categories, it is significantly affected by moisture which will reduce both strength and modulus.
A completely revamped experience for the 5th Generation and + Series of MakerBot 3D Printers. You can quickly swap between the reliability of the Smart Extruder+ or Tough PLA Extruder, and a new sandbox platform with the Experimental Extruder. Explore new materials, print faster with draft nozzles, and enjoy the same advanced jam detection, z-homing, and filament detection sensors as you have with the Smart Extruder+
These boards drive the stepper motors on the mightyboard (Makerbot Replicator 1, 2 and 2X motherboard). They are compatible with both Rev E and Rev G mightyboards (Ie All Makerbot Replicator Machines)
Key features:
• Actively Heated Chamber to 100°C
• ABS Optimizes Dual Extrusion
• Extra Large Build to 305 x 305 x 320mm
• Flexible heated build plate to 105°C
5% Bulk Discount available - Order 5 or more machines at once - Conditions apply
Chubbs the Purple Octopus is printed on a Makerbot Replicator 2 at 200 microns (each layer is only .2mm thick); using Bilby 3D brand PLA Purple. It takes 2 hours to print and has 3 Shells with 5% fill.
Size : 11cm tall. 10cm wide (at legs), 5cm at body.
Model designed by Andreas Boehler
This Bilby3D PLA filament is fluro yellow (it is a true fluro and glows under UV light).
It comes on our new plastic spools which are 20cm wide with an inner hole of 5.2cm and stand 8cm tall It is for 1.75mm Extruding machines like the Makerbots, UPs, Mbots and most modern machines
Melting Point 190-230 degC
100x Bulk Pack Blue Tape Precut Sheet (for Replicator 1,2,2X)
This is a 100 sheet pack of our die cut self adhesive Blue tape is designed to fit perfectly on the Makerbot Replicator 1, 2 or 2X, but can also be used on other 3D printers, to help PLA, Wood or Brick filaments prints stick to the bed. It is 28 x 16cm. The backing peels off for easy adhesion.
25x Bulk Pack Blue Tape Precut Sheet (for Replicator 1,2,2X)
This is a 25 sheet pack of our die cut self adhesive Blue tape is designed to fit perfectly on the Makerbot Replicator 1, 2 or 2X, but can also be used on other 3D printers, to help PLA, Wood or Brick filaments prints stick to the bed. It is 28 x 16cm. The backing peels off for easy adhesion.
This die cut self adhesive Blue tape is designed to fit perfectly on the Makerbot Replicator 1, 2 or 2X, but can also be used on other 3D printers, to help PLA, Wood or Brick filaments prints stick to the bed. It is 28 X 16cm. The backing peals off for easy adhesion. Price is per sheet (also available in bulk packs)
We manufacture this tape to have a strong adhesive and be better for PLA adhesion than painters tape, or Makerbot blue tape sheets
This heater cartrige has short (10cm long) cables with a molex male pin connector. The cartrige is 23mm long and 6mm in diameter. It is made in Australia by Bilby3D and is a non-genuine exchange for the Makerbot Replicator 2 and 2X heater cartrige.
Makerbot R2/2X- End stop cable (cable D) (rev 2) - UNTIL SOLD OUT
This cable is used to connect the X Y and Z endstop boards to the motherboard. It is used on the Markerbot Replicator Rev H (post sept 2013) 2 and 2 X machines, and includes 3 ferrits pre-fitted. IMPORTANT : This version is for Rev H motherboards. Not rev G - pre oct 2013. Also the X length is only 90cm long and requires an Endstop Jumper cable to be purchased separately.
Not used on the Replicator 1 Ply wood models, or rev G machines. If you have a rev G Replicator 2 or 2x - pre oct 2013 edition, those cables are now discontinued. You can fit this version with the jumpercable just ferrites are a bit tight for space under base plate. This is the cable only and does not include the endstop boards
This ribbon cable extrends the X Endstop cable. It connects to the X endstop and the XYZ endstop cable, providing extra length at the X motor end. All rev H Motor cables require this extrension.
This is a brushless fan, similar to that used in the Makerbot Replicator 2 with a nozzle attachement to blow cool air on the printout and rapidly set the plastic for better overhangs and thus higher resolution
Replicator 2 Power supply (refurb for Rev G or earlier mainboard)
Non Genuine Makerbot Power supply for rev G or earlier motherboards (24v,6A) with the male connector.
IMPORTANT : Rev H Replicator 2 machines use the same power supply! Also this power supply is not adeqate for dual extrusion and heated bed machines.
This insert slots easily into the left hand belt mount on a Makerbot Replicator 2 or 2X to fix wearing damage. It slots easily into the outside of the mount and allows you to tighten belts and start printing again without having to remove the rods and entire belt mount. Note : includes the plastic 3d printed part only, does not include pulley or rod. Please oil the rod regularly to prevent this occuring again.
Replicator 1/2 - Extruder Upgrade Kit (injection moulded) - Left Lever
This injection molded upgrade is designed to fit the Makerbot Replicator 1 Twin left extruder. IT DOES NOT FIT the Repliactor 2X which requires a thicker drive system. It also is NOT suitable for the Replicator 2 or single extruder machines!
This tube is an improvement over the stock MakerBot Replicator 1 and MakerBot Replicator 2 thermal barrier tube. Also used on many other types of 3D Printers
Simplify3D® is Integrated 3D Printing Software
Harness the power of your 3D printer and move up to better quality prints with Simplify3D® Software.
Import, repair, slice, preview and print… all from one integrated desktop application.
Simplify the process AND improve the end result. Both are possible!
Features:
- Build print files for a huge range of printers - all from one application which has both a quick and easy basic option AND an advanced option with control of more parameters than we have seen in any other software
- Support for printers from Printrbot, Makerbot, FlashForge, XYZprinting (DaVinci), Solidoodle, Ultimaker, Leapfrog, Airwolf, Lulzbot, Tinkerine, BFB, Rapman, Cubify, MendelMax and more. Full list here
- Unrivalled slicing performance: High speed slicing with great print quality
- Variable slicing settings: You can apply 40% infill at the base and 15% infill at the top, and change layer height at different heights in the model
- Advanced Multi-Part Printing: Even when printing multiple models at the same time, you can apply different settings for each model
Advanced Features:
- Intelligent support creation: You can create supports automatically, or add or remove them with the click of a mouse, or both!
- Variable slice settings: You can vary layer height, feed, speed, temperature and more within the one print job so you can achieve the perfect balance of speed and quality. With wood filament, you can vary the temperature during printing to create a wodgrain effect between layers
Sydney - Kingsgrove, NSW
Melbourne - Clayton, VIC
