This wear resistant nozzle by Micro Swiss is the standard size for a range of printers
It has a Wear Resistant High Lubricity TwinClad XT Coating this makes it a excellent choice when printing with abrasive/wearing material such as Bronze, Copper, Alumininium or Carbon Fiber filament.
FeaturesSpecsSupport
TwinClad XT is a nickel composite coating for very low frction. Over a 360 brass base, it gives a lower coefficient of friction than PTFE (Teflon) over nickel
This is dimensioned the same as our standard nozzle, as used on the Makerbot MK8 extruders.
ALWAYS run preheat before changing nozzles to avoid stripped threads.
Is is compatible with Makerbot:
- Makerbot Replicator 1 (Single and Dual)
- Makerbot Replicator 2
- Makerbot Replicator 2x
- Craftbot 2
- CraftBot PLUS
- BQ Witbox
- BQ Prusa i3 Hephestos
- CraftBot 2
- CraftBot PLUS
- BQ Witbox
- BQ Prusa I3 Hephestos
- Creality CR-10
- Creality CR-10-S5
- Creality CR-10-S4
- Creality CR-10S
- Creality CR-10 MINI
- Ender 2
- Ender 3
- TronXY X5S
- Tevo Tornado
- Anet A8 (Note Changing nozzle on a Smart Extruder is difficult and may void Smart Extruder warranty)
- Replicator 5th Gen
- Replicator Mini
- Replicator Z18
Next >
SpecsHole:0.4mm hole. Thread:M6, 5mm Long Total Length:13mm. Head width: 7mm Base Flat at screw/thread end Tipmay have a slight flatened area Filament Size: suitable for 1.75mm filament. CoatingTwinClad Coated
Product Dimensions: 12 x 8 x 8mm
Next >
This product has no specific warranty. Bilby 3D will honor obligations under Australia Consumer Guarantee regulations if and where they apply to this product
This wear resistant nozzle by AVN/Micro Swiss is the standard size for a range of printers
It has a Wear Resistant High Lubricity TwinClad XT Coating this makes it a excellent choice when printing with abrasive/wearing material such as Bronze, Copper, Alumininium or Carbon Fiber filament.
This wear resistant nozzle by Micro Swiss is the standard size for a range of printers has a 5mm long M6 thread, but has a larger and 0.6mm hole, which it sometimes used for faster printing and with metal and PETG filaments. Total Length 13mm
Buy Now
0.4mm Nozzle - M6 Thread for MK8 Extruders - Brass
This is the most common nozzle across all 3D Printers. Most notably Makerbot Replicator 1, 2 and 2x, Prusa, older FlashForge
Buy Now
Stainless Steel Barrel with TwinCladXT Coating
This tube is an improvement over the stock MakerBot Replicator 1 and MakerBot Replicator 2 thermal barrier tube. Also used on many other types of 3D Printers
This This wear resistant nozzle by AVN/Micro Swiss suits a range of printers with 1.75mm filament. It has an M7 thread and 0.2mm hole.
Buy Now
All Metal Hotend Kit for CR-10s PRO Printers
All Metal Hotend Kit for Creality CR-10s PRO / CR-10 Max / Ender 3 Neo / Ender 3 V2 Neo
Buy Now
HTPLA - 1.75mm - Bronze - 50g Coil - UNTIL SOLD OUT
Brick or cast bronze? Brush, polish, or patina and enjoy!
Introducing Bronze Composite HTPLA. Prints like plastic, but finishes like real metal for beautiful, durable parts from most standard 3D printers. So many finishing possibilities, but here are some ideas to get you started (see sample Protognomes in product photos):
Buy Now
Flashforge Barrel for Dreamer / Creator Pro / Inventor 1 - FFptfe
Genuine FlashForge barrel. It has a smooth outer tube with flats for holding with a spanner or pliers and a threaded end
Buy Now
PLA Blend Filament - Carbon Fiber - 2.85mm - 125g Coil - UNTIL SOLD OUT
This amazing filament is a blend of PLA and carbon Fiber by ProtoPasta in the USA. It prints easily at 230-245 degrees on a cold bed. We used glue on a glass bed for our test.
Buy Now
L Type Spanner - 7mm
This quality chrome vanadium steel spanner is perfect for undoing the nozzle on your 3D printer. Distance Across the flats, 7mm
Buy Now
HTPLA - 1.75mm - Brass - 500g Spool - UNTIL SOLD OUT
Brick or cast brass? Brush, polish, or patina and enjoy!
Introducing Brass Composite HTPLA. Prints like plastic, but finishes like real metal for beautiful, durable parts from most standard 3D printers. So many finishing possibilities, but here are some ideas to get you started (see sample Protognomes in product photos):
Buy Now
HTPLA - 1.75mm - Bronze - 500g Spool - UNTIL SOLD OUT
Brick or cast bronze? Brush, polish, or patina and enjoy!
Introducing Bronze Composite HTPLA. Prints like plastic, but finishes like real metal for beautiful, durable parts from most standard 3D printers. So many finishing possibilities, but here are some ideas to get you started (see sample Protognomes in product photos):
Buy Now
PLA Blend Filament - Carbon Fiber - 1.75mm - 50g Sample Coil - UNTIL SOLD OUT
This amazing filament is a blend of PLA and carbon Fiber by ProtoPasta in the USA. It prints easily at 230-245 degrees on a cold bed. We used glue on a glass bed for our test. Tendancy to leave small balls/pimples on surface which easily clean up. Will wear nozzle so we advise using a wear resistant nozzle (sold seperately). Produces impressively strong models with minimum fuss and difficulty.
Buy Now
Barrel for Flashforge Guider / Finder - FFptfe
Threaded metal tube that runs between the heater block and the circular heatsink in the extruder
Buy Now
All Metal Hotend Kit for CR-6 SE Printers
All Metal Hotend Kit for Creality CR-6 SE Printers
Micro Swiss Direct Drive Extruder is a drop in system for CR10 / Ender Printers. We include the MicroSwiss HotEnd.
No modification required, simple plug and play
No printed brackets or sandwiches
Buy Now
PLA Blend Filament - Carbon Fiber - 1.75mm - 500g - UNTIL SOLD OUT
This amazing filament is a blend of PLA and carbon Fiber by ProtoPasta in the USA. Will wear nozzle so we advise using a wear resistant nozzle (sold seperately). Produces impressively strong models with minimum fuss and difficulty.
Buy Now
PLA Blend Filament - 1.75mm - Stainless Steel - 500g Spool - UNTIL SOLD OUT
Proto-pasta Stainless Steel PLA is a dense material that prints as easily as standard PLA but results in heavy prints that can be finished post-print to achieve amazing results. Perfect for jewelry, costumes, props, figurines, crafting, robots, and more!
In filament form, SSPLA is slightly more brittle than standard PLA, and requires extra care when handling.
Processing is comparable to standard PLA (extrudes at 190-240C). No heated bed required. Due to increased brittleness, process may be less consistent on smaller nozzles and/or bowden type machines.
Buy Now
PLA Blend Filament - 1.75mm - Conductive - 500g Spool - UNTIL SOLD OUT
Have you ever wanted to create something with your 3D printer that includes electronics? Maybe an LED, touch sensor, or some other genius invention to solve the worlds problems? Then Proto-pasta Conductive PLA is the perfect material for you! Prints at standard PLA settings on a non-heated bed.
Buy Now
HTPLA - 1.75mm - Copper - 50g Coil - UNTIL SOLD OUT
Terracotta or cast copper? Brush, polish, or patina and enjoy!
Introducing Copper Composite HTPLA. Prints like plastic, but finishes like real metal for beautiful, durable parts from most standard 3D printers. So many finishing possibilities, but here are some ideas to get you started (see sample Protognomes in product photos):
Buy Now
Micro Swiss Extruder + HotEnd for Creality Ender 5 Printers
Micro Swiss Direct Drive Extruder is a drop in system for Ender 5 Printers. We include the MicroSwiss HotEnd.
No modification required, simple plug and play
No printed brackets or sandwiches
Buy Now
PLA Blend Filament - Magnetic Iron - 1.75mm - 125g Coil - UNTIL SOLD OUT
This amazing filament is a blend of PLA and carbon Fibre by ProtoPasta in the USA.
Proto-pasta Magnetic Iron PLA - as its name implies - responds to magnets and behaves similarly to pure iron, even to the point of rusting! Magnetism opens up a new world of practical applications and fun creations.
It extrudes at 190-200 degrees c on a cold bed. We have tested on buildtak wit glue stick and it sticks well. Prints best at thicker resolutions like 300 microns, but will look like 100 micron. Our tests showed no spider webbing at all, and models held water after printing. It can lift in unsupported areas, but quickly recovers on the next layer. Sands nicely with very course sandpaper. Can get rust effect by submerging in with salty water for 2-3 hours. In our tests it was not too abrasive on nozzle, but recommend a wear resistant nozzle.
Buy Now
Capricorn Teflon tube for Flashforge Single Extruder Barrel - FFptfe
This short piece of Teflon tubing is for lining the barrel on the Flashforge Guider, Guider2, Finder, Finder Plus and Inventor 2
Made from Capricorn Tubing, it is higher lubricity and more resistant to the high temperatures experiences in a hot end
Buy Now
Teflon tube for Flashforge Single Extruder Barrel - FFptfe
This short piece of Teflon tubing is for lining the barrel on the Flashforge Guider, Guider2, Finder, Finder Plus and Inventor 2
All prices are in Australian Dollars and include GST. Standard Postage & Handling with Australia is $12 flat rate, free for orders over $350. Express Post starts at $15
Sydney - Kingsgrove, NSW
Melbourne - Clayton, VIC
