CarbonX™ Carbon Fiber PA12 is made using high-modulus carbon fiber and a specialty Nylon 12 (PA12) that we chose for its printability, thermal properties, and chemical resistance. PA12 is widely used in a variety of industries due to its excellent chemical resistance, low moisture absorption, and wide processing window. This formulation ensures very low shrinkage in the printed part resulting in excellent dimensional stability. This makes CF-PA12 an excellent choice for tools, fixtures, and jigs.
FeaturesSpecsSupport
Note: This filament is certified under Raise3Ds Open Filament Program, so a profile is available in the ideaMaker Library, ready to go.
- Extruder: 265-285°C, potentially higher depending on printer
- Bed Temp: 90-110°C [heated bed required]
- Bed Prep: Nano Polymer Adhesive
- Hardened Nozzle: 0.4mm or larger v
- Layer Height: Ideal layer height is 60% of nozzle diameter. We do not recommend printing layers below 0.25mm with carbon fiber grades. Lower than 0.25mm may create too much back pressure in the hot end and result in poor feeding, jams, drive gear clicking, and eating a notch into the filament
- Moisture & Filament Storage: PA12 absorbs less moisture than standard PA6-based materials (PA6, PA6/66, PA6/69), but it still absorbs moisture and must be dry before printing. Keep in sealed container between uses and dry at 90c for 4-6 hours if filament does become exposed to moisture and it becomes too wet to print
Product Dimensions: 210 x 230 x 80mm
Next >
This product has no specific warranty. Bilby 3D will honor obligations under Australia Consumer Guarantee regulations if and where they apply to this product
Material Safety Data Sheet
Raise3D Premium PVA PLUS Support Material - 1.75mm - Natural - 750g
Raise3D Premium PVA+ is a polyvinyl alcohol (PVA)-based cold water-soluble support filament for FFF 3D printing with dual extruders.
*Note- Not detectable In optical filament sensors as on Raise 3d Printers
Carbon Fiber reinforced PEEK 3D Printing Filament is ideal for the most demanding applications
Buy Now
Spectrum Nylon, PA6 Carbon Fibre, 1.75mm, 500g - UNTIL SOLD OUT
High temperature construction material
Nylon PA6 CF15 is a high-temperature, black, PA6-based construction material. Filling with 15% carbon fibres increases significantly the mechanical strength of the polyamide the material is based on. The filaments specific quality is the moisture absorption reduced by half and the water absorption time is four times lower than that of the pure PA6. Printing does not require a heated chamber and no deformation occurs. The material is compatible with the HIPS and BVOH support materials. In addition, Nylon PA6 CF15 features a very low linear shrinkage (up to 0.1%), a high deformation temperature (240°C), working temperature (180°C) and low thermal expansion coefficient (0.4 10-5/K).
PolyMide™ PA6-CF is a carbon fiber reinforced nylon (PA6) 3D printing material offering the highest strength, impact resistance and heat deflection of all Polymaker 3D printing materials.
Buy Now
Kimya ABS + Kevlar Fibre - 1.75mm - Black - 500g Spool
ABS KEVLAR has been deisgned for 3D printing by a precise formulation of aramid fibers into ABS materials.
CarbonX™ CF-HTN is an advanced semi-aromatic polyphthalamide (PPA) reinforced with high-modulus carbon fiber. This polymer is widely used for metal replacement applications that must resist high mechanical loads at elevated temperatures and aggressive chemical environments. HTN has traditionally been a go-to material for demanding applications in automotive, aerospace, oil & gas, electrical, electronics, and industrial markets.
PolyMide™ PA612-CF is a carbon fiber reinforced nylon filament based on a copolymer of Nylon 6 and Nylon 12. Featuring 15% chopped carbon fibers by weight, this filament has lower moisture sensitivity compared to PA6/66 and PA6-based materials, and better mechanical properties than PA12-based materials.
PolyMide™ PA6-CF is a carbon fiber reinforced nylon (PA6) 3D printing material offering the highest strength, impact resistance and heat deflection of all Polymaker 3D printing materials.
All prices are in Australian Dollars and include GST. Standard Postage & Handling with Australia is $12 flat rate, free for orders over $350. Express Post starts at $15
Sydney - Kingsgrove, NSW
Melbourne - Clayton, VIC
